Leave Your Message

Mws Litz Wire For High-frequency Transformer And Wireless Charging Coils

Optimizing High-Frequency Power Conversion and Inductive Power Transfer with Advanced Multistrand Magnet Wires.

The Role of MWS Litz Wire in Modern High-Frequency Systems

In the rapidly evolving landscape of power electronics, the demand for higher efficiency, power density, and thermal management has never been more critical. High-frequency switch-mode power supplies (SMPS), resonant converters, and wireless charging systems are pushed to operate at higher frequencies—ranging from tens of kilohertz to several megahertz. However, operating at these frequencies introduces significant electromagnetic challenges, specifically the skin effect and proximity effect.

💡
What is Skin Effect? At high frequencies, alternating current (AC) does not distribute evenly throughout a conductor. Instead, it concentrates near the surface (the "skin"). This reduces the effective cross-sectional area of the wire, dramatically increasing AC resistance ($R_{ac}$) and causing excessive heat dissipation.

Similarly, the proximity effect occurs when the magnetic field generated by adjacent turns of a winding influences the current distribution within neighboring wires, forcing the current into restricted regions and further compounding power losses. MWS Litz wire is specifically engineered to mitigate these losses. By bundling multiple, individually insulated fine wire strands in a precise, transposed configuration, Litz wire ensures that each strand occupies all possible radial positions throughout the length of the conductor. This balances the magnetic flux and forces current to distribute equally among the strands, dramatically lowering the AC resistance.

Why MWS Specifications Matter

MWS (Micro Wire Specialization) standards define strict tolerances, high-quality copper purity, and advanced insulation formulations. Utilizing MWS Litz wire in high-frequency transformers and wireless charging coils allows design engineers to achieve optimal Q-factors (quality factors), maximize coupling efficiency, and reduce thermal stress. Whether it is a compact medical wireless charging pad or a multi-kilowatt traction transformer for electric vehicles (EVs), selecting the correct Litz wire configuration is the foundation of high-efficiency magnetics design.

Key Advantages

  • Reduced AC Losses: Minimizes skin and proximity effects at frequencies up to 3 MHz.
  • High Q-Factor: Essential for maximizing wireless power transfer efficiency.
  • Thermal Management: Lower resistance results in cooler operating temperatures and longer component lifespan.
  • Space Efficiency: Allows for ultra-compact transformer designs in GaN and SiC systems.

Company Profile

Zhuhai Transmo Technology Co., Ltd is a professional enameled wire manufacturer for fine and ultra fine enameled wire, rectangular wire as well as Litz wire. The finest wire diameter reach 10 micron. TRANSMO have been a leading supplier for self-bonding wire and High Tension Wire. All the wire can be produced according to industry standards such as IEC 60317, NEMA MW1000, JIS C3202 or to customer specific requirements. TRANSMO’s wires is widely used in consumer electronics, telecommunication, automotive, new energy, IT industry and medical equipment.

2015
Established In
20+
Export Destinations
780+
Serving Customers

Industrial & Commercial Landscapes: The Switch to WBG Semiconductors

The global power electronics market is undergoing a seismic shift driven by the commercialization of Wide Bandgap (WBG) semiconductors, such as Silicon Carbide (SiC) and Gallium Nitride (GaN). These advanced semiconductors allow switching frequencies to scale from traditional limits of 50 kHz up to 500 kHz or even several MHz. Higher switching frequencies enable the use of smaller passive components (transformers and inductors), reducing the overall footprint of power converters.

⚙️
The Magnetics Bottleneck: While GaN and SiC switches can easily process megahertz frequencies with minimal loss, traditional solid copper magnet wires cannot. At these frequencies, solid wire behaves like an insulator in its core, forcing all current to the outer boundary. Without MWS Litz wire, the magnetic component becomes the primary bottleneck, limiting efficiency and causing catastrophic thermal runaways.

Consequently, industries such as electric vehicle (EV) charging infrastructure, onboard chargers (OBCs), renewable energy inverters, and data center power supplies have widely adopted Litz wire as the default conductor technology. For instance, in solar string inverters, using custom-designed MWS Litz wire in the boost inductors and main transformers has pushed efficiency ratings past 99%. In server power supplies, where space is at an absolute premium, planar transformers utilizing ultra-fine Litz wire allow for high power density profiles that fit easily into standard rack units.

Deep-Dive Application Scenarios

1. High-Frequency Transformers in EV and Industrial Power Conversion

In electric vehicle onboard chargers (OBC) and DC-DC converters, space, weight, and efficiency are tightly constrained. The converter must step down the high battery voltage (often 400V or 800V) to low voltage lines (12V/24V) to power auxiliary systems. High-frequency transformers operating at 100 kHz to 300 kHz are critical in these topologies. By utilizing MWS Litz wire with specialized insulations like Polyimide (Kapton) wrapping, manufacturers can achieve high breakdown voltages (up to 4kV or higher) while maintaining thin profiles. The multi-strand configuration ensures that skin depth at 200 kHz is perfectly matched to individual strand diameters (typically 0.1mm or thinner), keeping copper losses at a bare minimum.

2. Wireless Charging Coils for Consumer and Automotive Systems

Wireless power transfer (WPT) relies on magnetic resonance coupling between a transmitter coil (Tx) and a receiver coil (Rx). The efficiency of this transfer is directly proportional to the Quality Factor ($Q$) of the coils, defined as:

Q = ωL / R

Where $\omega$ is the angular frequency, $L$ is the inductance, and $R$ is the AC resistance. To maximize $Q$, $R$ must be kept as low as possible. In Qi-compliant smartphone chargers operating around 87-205 kHz, self-bonding Litz wire allows for the winding of rigid, coreless coils that maintain their shape without additional structural plastics. In high-power EV wireless charging pads (operating at 85 kHz under the SAE J2954 standard), currents can reach dozens of amperes. Here, heavy-duty Litz wire consisting of thousands of strands of 0.1mm wire is utilized to handle the high current density while preventing overheating, ensuring safe and rapid energy transfer.

Advanced Production Equipment & Quality Control

With more than 15 years' experience in manufacturing enameled wire, TRANSMO people adopt advanced drawing machines and enameling machines, precise processing technology, and seriously quality control to produce wire with reliable and consistent quality. From incoming material, semi product, final product and delivery, the whole process is well recorded and monitored, the advanced code management allow our products with unique code and production is traceable.

International Trade & Global Exhibitions

TRANSMO supplied wires worldwide for 780 customers in more than 20 countries. We are experienced in international trade, we know how to understand the need and concern of customer, how to deliver goods to customer in any place in time. Our active participation in global electronics and magnetics exhibitions allows us to stay at the forefront of industrial requirements and build close partnerships with global engineering teams.

Main Transmo Exhibition Booth
Customer ConsultationProduct Display BoardTechnical Seminar DiscussionInternational Business MeetingEnameled Wire Showcase

Technical Selection Guide: Matching Frequency to Strand Gauge

When designing high-frequency transformers or wireless charging coils, selecting the correct individual strand diameter is paramount. The general engineering rule of thumb is that the strand radius should be less than or equal to the skin depth at the target operating frequency. The table below outlines the industry standard recommendations for MWS Litz wire strand selection:

Frequency Range Recommended Strand Size (AWG) Nominal Strand Diameter (mm) Target Applications
60 Hz - 1 kHz 28 AWG - 30 AWG 0.32 mm - 0.25 mm Audio Transformers, Low-Freq Inductors
1 kHz - 10 kHz 33 AWG - 35 AWG 0.18 mm - 0.14 mm High-Power UPS, Induction Heating Coils
10 kHz - 100 kHz 38 AWG - 40 AWG 0.10 mm - 0.08 mm EV Wireless Charging Pads, Solar Inverters
100 kHz - 350 kHz 42 AWG - 44 AWG 0.063 mm - 0.05 mm EV Onboard Chargers (OBC), SMPS Transformers
350 kHz - 1 MHz 46 AWG - 48 AWG 0.04 mm - 0.03 mm GaN-based LLC Converters, Smartphone Qi Coils

Note: Operating at frequencies above 1 MHz typically requires ultra-fine strands of 48 AWG to 50 AWG to maintain a high Q-factor and control proximity losses within tightly wound transformer windows.

Certificates & Honors

Our commitment to quality is backed by international standards. TRANSMO operates under strict quality management frameworks to ensure that every spool of wire delivered meets the high reliability demanded by automotive, medical, and industrial customers worldwide.

ISO Quality Management Certificate
Environmental Compliance Certificate
UL Safety Certification
RoHS Compliance Report
REACH Declaration
IATF 16949 Automotive Certificate